BQPKY - FORGE BLACK LATEX HP 10 45599

  • MSDS: BQPKY
  • Manufacturer: VALSPAR CORP THE
  • Product Name: FORGE BLACK LATEX HP 10 45599
  • National Stock Number: 8010-00N012686
Product Identification

Product ID:FORGE BLACK LATEX HP 10 45599
MSDS Date:08/20/1990
FSC:8010
NIIN:00N012686
MSDS Number: BQPKY

Responsible Party
VALSPAR CORP, THE
1101 THIRD ST S
MINNEAPOLIS, MN 55415-1211
US

Emergency Phone: 612-332-7371

Info Phone: 612-332-7371

Cage: 23526

Contractor
VALSPAR CORPORATION
MINNEAPOLIS, MN 55415 US

Telephone: 612-332-7371/888-345-5732

Cage: 23526

Ingredients

MICA SILICATE (MUSCOVITE MICA). RESPIRABLE DUST WITH <1%

CAS: 12001-26-2

RTECS: VV8760000

Fraction By Weight: 1%

OSHA PEL 20 MPPCF

ACGIH TLV: 3 MG/M3 RDUST; 9293


CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

Fraction By Weight: 1 - 5%

OSHA PEL 3.5 MG/M3

ACGIH TLV: 3.5 MG/M3


ETHYLENE GLYCOL (1,2-ETHANEDIOL)

CAS: 107-21-1

RTECS: KW2975000

Fraction By Weight: 5%

OSHA PEL 50 PPM C

ACGIH TLV: 50 PPM C VAPOR

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

Hazards

LD50 LC50 Mixture:N/K
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PROLONGED OVEREXPOSURE MAY CAUSE
PNEUMOCONIOSIS. CONTAINS INGREDIENTS WHICH MAY CAUSE LIVER, KIDNEY
AND NERVOUS SYSTEM DAMAGE.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:EYES:OVEREXPOS TO INGRED MAY CAUSE
IRRIT,POSSIBLE DELAYED IRRITATION.SKIN:OVEREXPOS TO INGRED MAY
CAUSE DELAYED SKIN IRRITATION.MAY BE ABSORBED.INGEST:OVEREXPOS TO
INGRED MAY CAUSE GASTROINTESTINAL TR ACT IRRITATION,NAUSEA,AND
VOMITING.INHAL:OVEREXPOS TO INGRED MAY CAUSE RESPIRATORY TRACT
IRRITATION,NAUSEA,AND VOMITING.
Medical Cond Aggravated by Exposure:ANY RESPIRATORY OR SKIN CONDITION.

First Aid

First Aid:EYES:FLUSH IMMEDIATELY WITH PLENTY OF WATER FOR 15 MINUTES
AND GET MEDICAL ATTENTION. SKIN:WASH THOROUGHLY WITH SOAP AND
WATER. INGESTION:INDUCE VOMITING IMMEDIATELY AS DIRECTED BY MEDICAL
PERSONNEL. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
INHALATION:IF AFFECTED BY VAPOR OR SPRAY MIST, REMOVE TO FRESH AIR.

Fire Fighting

Flash Point:205F,96C
Lower Limits:1.00
Upper Limits:15.00
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL, FOAM AND/OR WATER
FOG.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .USE WATER SPRAY TO COOL CONTAINERS EXPOSED TO FIRE.
Unusual Fire/Explosion Hazard:NONE. HAZARDOUS DECOMPOSITION
PRODUCTS:HALIDES, CARBON DIOXIDE, CARBON MONOXIDE, METAL OXIDES.

Accidental Release

Spill Release Procedures:VENTILATE AREA. REMOVE SPILL WITH INERT
ABSORBENT.
Neutralizing Agent:N/K

Handling

Handling and Storage Precautions:KEEP CNTNRS NOT IN USE CLSD.DO NOT
STORE ABOVE 120F,48.89C.KEEP FROM FREEZING.EMPTY CNTNRS MAY CONTAIN
PROD RESIDUE.DO NOT CUT,PUNCTURE OR (SEE SUPP)
Other Precautions:N/K

Exposure Controls

Respiratory Protection:WEAR APPROPRIATE, PROPERLY FITTED RESPIRATOR
(NIOSH/MSHA APPROVED) DURING AND AFTER APPLICATION UNLESS AIR
MONITORING VAPOR/MIST LEVELS ARE BELOW APPLICABLE LIMITS. FOLLOW
RESPIRATOR MANUFACTURER'S DI RECTIONS FOR RESPIRATOR USE.
Ventilation:REQUIRED WHEN SPRAYING OR APPLYING IN CONFINED AREA.
Protective Gloves:USUAL HAND PROT FOR PAINT APPLICATION.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:USUAL CLOTHING FOR PAINTING OPERATIONS.
Work Hygienic Practices:N/K
Supplemental Safety and Health
VAPOR PRESSURE:24 MMHG AT 77F,25C. FLASH POINT METHOD:TCC/PMCC.
HANDLING AND STORAGE PRECAUTIONS:WELD CONTAINERS. ALL LABEL
WARNINGS MUST BE OBSERVED UNTIL CONTAINER HAS BEEN CLEANED,
RECONDITIONED OR PROPERLY DISPOSED OF.

Chemical Properties

HCC:N1
Boiling Pt:B.P. Text:212F,100C
Melt/Freeze Pt:M.P/F.P Text:N/K
Decomp Temp:Decomp Text:N/K
Vapor Pres:SEE SUPP
Vapor Density:2.1,AIR=1
Spec Gravity:1.26,WATER=1
Evaporation Rate & Reference:0.4,BUTYL ACETATE=1
Solubility in Water:YES
Appearance and Odor:NORMAL FOR A COATINGS PRODUCT.
Percent Volatiles by Volume:63.24

Stability

Stability Indicator/Materials to Avoid:YES
WATER-REACTIVE MATERIALS.
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:HALIDES, CARBON MONOXIDE, CARBON
DIOXIDE, METAL OXIDES.
Conditions to Avoid Polymerization:WILL NOT OCCUR

Disposal

Waste Disposal Methods:DISPOSE IN CHEMICAL DISPOSAL AREA OR IN A MANNER
THAT COMPLIES WITH FEDERAL, STATE AND LOCAL REGULATIONS. DO NOT
INCINERATE CLOSED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.